Dig up corn to put more money in your pocket
Drive by Leon Knirk’s farm one day this fall and you might catch sight of him digging up corn plants with a shovel. No, he hasn’t lost his mind. He’s in the process of evaluating what he refers to as corn’s money roots—the first, second and third set of crown roots.
These three sets of crown roots supply the bulk of nutrients and moisture to corn, making them essential for high corn yields. Their appearance tells Knirk a story he can read in 30 seconds or less. In that brief span of time, he sees the impact his tillage program has had on his corn crop’s growth and development. If the money roots are growing like they should, the Quincy, Mich., farmer can anticipate harvesting more corn this fall. The opposite is true, too, if his tillage practices have created a density layer—a zone of packed dirt beneath the soil surface that can extend horizontally across a field and impede corn-root growth.
Corn roots are designed to grow down deep into the soil at a 35° to 40° angle, says independent agronomist Bill Bauer, who led a session on the topic at the Farm Journal Corn College Fundamentals event in Michigan. He says if there’s no obstruction—no compaction and no density layer—corn roots grow vertically as long as they have access to water and oxygen. However, if the roots hit an obstruction, they will turn and grow horizontally, or sideways. "When we’re turning a lot of roots, that puts limitations on the crop," he says.
When roots turn and grow sideways, the corn plant is unable to effectively absorb nutrients and moisture that might be deeper in the soil profile as summer progresses. This results in less productive plants that are vulnerable to pests, disease and standability issues.
"There’s no sense in spending money to increase nitrogen or push populations for higher yields in a scenario where plants are hitting a density layer because they can’t respond the way you want them to," Bauer explains.
Farmers who run a disk or field cultivator in poor conditions don’t realize the negative impact those tools have on soil structure below ground. Corn yields can suffer significantly as a
result, says Brad Beutke, who also presented at the Corn College event.
"In extremely wet or dry years, when a horizontal density layer has its greatest impact, we’ve seen 70- to 80-bu. differences in those fields compared to fields where the roots can grow down like they’re supposed to," Beutke adds.
In Bauer’s experience, shallow density layers, within the top 4" are more detrimental to yield than layers deeper in the soil profile. He tells farmers to use a tile probe to get an idea if a density layer or obstruction is present.
"Make a note of anything that stops your probe," Bauer says. "It might be a density layer you hit."
Bauer tells farmers when they dig up the corn plant to insert their shovel outside of where the planter gauge wheels ran; then dig 8" to 9" deep all around the plant. "If a density layer is present, the soil will naturally want to break at that layer, so you’ll know that’s where the problem is," he says.
Harvest priorities. Potential density layers are what Knirk looks for when he evaluates corn crown roots late in the season. Hybrids affected by them almost always have endured moisture and nutrient stress, which result in premature stalk cannibalization.
"Those are the ones I’ll want to harvest first in the fall," Knirk says. "If you don’t have any good nodes left, the stalk begins to get pithy and might increase stalk rot."
Knirk checks each hybrid he grows on a field-by-field basis prior to harvest. Typically, he checks a few stalks in each corn hybrid, making sure to pick those that are representative of the plants within the field.
"The process takes a few minutes initially, but it gets easier and faster to do once you get over the mental aspect of cutting down your own corn," Knirk says, with a chuckle.
Along with establishing harvest priorities, crown-root checks can help farmers adjust their fall tillage practices to minimize the development of density layers, Beutke says. Vertical tillage can help, as long as farmers implement the process as a system and not as a single tillage pass.
"We need to think about what we’re doing in the fall before making our secondary tillage pass the following spring," Beutke says. "Depending on what you see in the field, you might want to run an inline ripper or hybrid chisel to remove density layers. Leaving a level surface in the fall is more important as growers switch to vertical-type, secondary tillage tools."
Beutke also suggests doing early season crown root checks in the V5 to V6 growth range, as the crop begins to set its maximum yield potential.
Don’t spend a lot of time or worry about needing any fancy equipment to evaluate your money roots, Bauer adds: "Everyone can carry a shovel into their fields to dig up corn and look for density layers."
Click here to view the step-by-step guide "How to Conduct an In-Field Analysis"
You can e-mail Rhonda Brooks at firstname.lastname@example.org.
- September 2013